FAQsUpdated 24 days ago
How long does the unit take to fully assemble?
Times on assembly will vary. If you are a beginner first time build, assembly can take anywhere from 4-6 hours. Expert level builders can complete it in as little as 1 hour.
Where can I locate my serial number?
The serial number will be located on the user left base in front of the weight stacks on a white sticker.
What lubricant do you recommend for the unit and what needs to be lubricated?
We recommend using Teflon Based lubricant on all chroming every 3 to 6 months. This includes the Guide Rods your weights utilize, as well as the front shafts on the unit. Please do not use WD-40 or other products besides the recommended Teflon Based Lubricant.
How do I properly install the weight plates for the units?
Please install the plates with the smooth surface side up. The small platforms/feet should be facing downwards. Please also make sure the weight stack number indent is facing towards the inside of the machine.
How much space do I need for the unit?
We recommend a space with a level surface and a clear or usable space of approximately 89 inches in width and 52 inches in depth. You’ll also need a ceiling taller than 96 inches for workable space, but the assembled unit stands at 84 inches tall once complete.
What are the dimensions of the Centr 3?
The Centr 3 is 46 inches long, 59 inches wide and 84 inches tall.
How tall is the unit without the pull up bar?
Unfortunately, the pull up bar cannot be removed.
Can I remove the pull up bar without affecting the structure of the unit?
Unfortunately, the pull up bar cannot be removed.
Can I install the unit without the top cross bar?
Unfortunately, the pull up bar cannot be removed.
How much space is on the inside of the unit?
The space inside the unit is 45 inches long and 47 inches wide.
Can I upgrade the weight stacks of the unit?
Unfortunately, the weight stacks cannot be upgraded.
How much does one of the main frame stations weigh?
One of the main frames weighs 65 pounds.
How much does the entire unit weigh?
The Centr 3 complete unit weighs 631 pounds, or 286 kgs.
Can I place my unit outside?
Unfortunately, the unit is not meant to be in an outdoor setting.
Are the sliders interchangeable?
Unfortunately, the sliders are not interchangeable.
How heavy is each weight plate?
Each weight plate is 10 pounds.
How much weight am I lifting per weight stack?
The Centr 3 has a resistance ratio of 2:1 per pulley, which means the maximum weight you can lift per pulley is 82.5 lbs per pulley.
How much space do I require on the back of the unit?
We recommend at least 6 inches from the wall. However, the unit can be pushed all the way back against a wall if necessary.
How much space do I require on the front of the unit?
We recommend at least a foot of space in front of the unit, but this really depends on how much exercise space you require to conduct your workouts.
How much space do I require on the sides of the unit?
We recommend at least a foot of space on each side. However, if space is tight, we recommend 6 inches. It really depends on the required space for you to properly conduct your workouts.
How much does the cable extend from the carriage? (How long/weight stem max out)
The cable can extend up to 98 inches before the top plate hits the top of the machine.
What is the Highest/Lowest Position the Carriage/Swivel pulley assembly reaches?
The Highest position will be 68 inches. The lowest position would be 11 inches.
What is the highest/Lowest set position/usage for red Smith Bar?
The Highest position will be 73.5 inches. The lowest position would be 15 inches.
What is the length of the pull up bar from end to end?
The length is 38 inches.
What is the length of the pull up bar from the interior, short end?
The length is 11 inches.
Am I able to hang another bench on the bench rack (not Inspire)?
If the bench you’re hanging has a handle or hanging mechanism that fits the width of our bench mount, then yes you can.
What are the resistance ratios of each pull point?
Each pull point is 2:1 ratio.
How much does the red Smith Bar weigh?
The Smith Bar, without weight pinned on the weight stacks and the bar is not attached to the carriages weights 17 lbs. The Smith Bar and carriages, without any weight plates pinned weighs 37 lbs.